Legrand RFB Series Floor Boxes Manual de usuario descargar pdf

RFB Series Floor Boxes

I N S T A L L A T I O N I N S T R U C T I O N S

nstallation Instruction No.: 1 007 256R2 – Updated January 2012

Legrand/Wiremold electrical systems conform to and should be properly

grounded in compliance with requirements of the current National

Electrical Code or codes administered by local authorities.

All electrical products may present a possible shock or fire

hazard if improperly installed or used. Legrand/Wiremold electrical

products may bear the mark as UL Listed and/or Classified and

should be installed in conformance with current local and/or the

National Electrical Code.

IMPORTANT: Please read all instructions

before beginning.

BEFORE CONCRETE POUR:

Step 1. Determine box location and conduit layout.

Step 2. Take off box top by removing two (2) #8-32 screws

attaching cover to base.

Step 3. Remove necessary knockouts. Attach conduit and

fittings (not supplied by Wiremold) to steel base.

Step 4. Configure adjacent compartments.

RFB4E Series Boxes are configured with solid removable

partitions that can be discarded for wire pass through.

Replace #8 screw back into base after barrier removal.

RFB Series Floor Boxes and Activations are UL Listed for use with tile, terrazzo and carpet covered concrete floors.

RFB6 and RFB6-OG Floor Boxes and Activations are also UL Listed for use with floors of wood construction.

PRODUCTS: Floor Box Cat. Nos.: RFB4E, RFB4E-OG, RFB6, RFB6-OG, RFB6E, RFB6E-OG

Device Plate Cat. Nos.: RFB6B, RFB6DP, RFB6GFI, RFB6S1, RFB6S2, RFB6RT, RFB6EXT,

RFB62A, RFB6-AAP

Furniture Feed Kit Cat. Nos.: RFB4KIT, RFB6KIT

Bare Concrete & Terrazzo Ring Cat. Nos.: RFB4E-CTR, RFB6E-CTR

(2) #8-32 Screws

Remove KOs & attach

Fittings and Conduit

RFB4E – Remove and discard

Barrier for pass through

Replace #8 Screw after

removing Barrier

RFB6 & RFB6E – Remove Plug and replace

with Bushing as required for pass through

Step 5. Re-attach box cover to base with two (2) #8-32 screws

removed during Step 2.

RFB6 and RFB6E Series Boxes are configured with

non-removable partitions containing pre-installed

plugs. Depending on wiring configuration, plugs may

be replaced with included bushings for wire pass

through. This may be done pre- or post-pour.

1 2 3 4 5 6

Indice de contenidos

Pagina 1 - RFB Series Floor Boxes

RFB Series Floor Boxes I N S T A L L A T I O N I N S T R U C T I O N SInstallation Instruction No.: 1 007 256R2 – Updated January 2012Legrand/Wire

Pagina 2 - CONCRETE POUR:

2AFTER CONCRETE POUR:WARNING: Pours of 1/4” (6 mm) or more over box housing willmake it difficult to break out the mud cap and causeexcessive concrete

Pagina 3

3Step 9. Remove mud cap from box and clean out anydebris from inside of box.Chip out concrete andlift out Mud CapRemove two (2) #8 Screwssecuring the

Pagina 4

4Step 12. RFB6KIT Furniture Feed Barrier Kit for use with FloorPortTMFPFF Furniture Feed Series Activations on RFB6 floor box.(2) #8 Mounting Screws(f

Pagina 5

5Step 13. RFB4KIT Furniture Feed Barrier Kit for use with Evolution6CFFTC Furniture Feed Activation on RFB4E floor box.Step 13A. Insert lower barrier

Pagina 6 - WIREMOLD

WIREMOLDU.S. and International: 60 Woodlawn Street • West Hartford, CT 061101-800-621-0049 • FAX 860-232-2062 • Outside U.S.: 860-233-6251 Canad

Modelos relacionados RFB6KIT | RFB6-AAP | RFB6EXT | RFB6B | RFB6RT | RFB62A | RFB6DP | RFB6GFI | RFB6S1 | RFB6S2 | RFB6 | RFB6-OG |

Comentarios a estos manuales

Sin comentarios

Legrand RFB Series Floor Boxes Manual de usuario

Busca en linea o descarga Manual de usuario para Hardware Legrand RFB Series Floor Boxes. Legrand RFB Series Floor Boxes User Manual Manual de usuario

Indice de contenidos

Modelos relacionados RFB6KIT | RFB6-AAP | RFB6EXT | RFB6B | RFB6RT | RFB62A | RFB6DP | RFB6GFI | RFB6S1 | RFB6S2 | RFB6 | RFB6-OG |

Comentarios a estos manuales

Relacionado con productos y manuales para Hardware Legrand RFB Series Floor Boxes